Installing A Bath tub
Installing A Bath tub
Blog Article
This great article below on the subject of How to Install a Bathtub is without a doubt engaging. Check it out for yourself and see what you think of it.
Installing a tub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging task. If the old tub is readily easily accessible, the project can relocate immediately; if you have to open up a wall to get rid of the old tub and place the new tub, the task is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. See to it you have certified yourself for the task and fit attempting it. Instead of working with a specialist to take over a halfway-completed job, it is better to think about using one prior to you begin. Opportunities are you might require a specialist plumber to make tube links.
This article will certainly help you set up a brand-new bathtub in your shower room if you have already acquired a new bathtub and do not require to transform the arrangement of your previous water pipelines.
Your devices and product checklist should comprise the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, activate the faucets to drain any water remaining in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the restricted accessibility that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will originate from the pipelines. As soon as the supply pipelines have been removed, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
Prior to moving on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washers are in place between the tap and the sink. Protect the tap in place with the producer offered backnut. When the tap is securely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The former type must be linked to the tap ends first, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Using the two wood boards under its feet, put the bathtub in the called for placement. The wooden boards are useful in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four little points.
The following objective is to ensure that the bath tub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the tub until the level reviews level.
To mount taps, fit all-time low of the outermost flexible faucet connector to the suitable supply pipeline by making a compression join; after that do the very same for the various other tap.
Activate the water system and examine all joints and brand-new pipework for leaks as well as tighten them if essential. Fill up the bath tub and additionally check the overflow outlet and also the regular outlet for leakages.
Finally, deal with the bath paneling as explained in the maker's instruction manual. Tiling and also sealing around the bath tub should wait up until the bathtub has actually been used at the very least once as this will certainly settle it right into its final placement.
Preparing for the Installation
To start with, the supporting framework provided with the bath must be fitted (if required) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to avoid pressure on the tub.
Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last position.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bath and also the tiling, resulting in complications with moisture and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes as well as cartridges, and are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealer can fracture relatively early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently available on the market. It is suggested to fit the tiles using water-resistant or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our part about How to Install a Bathtub. Thanks so much for spending some time to read through our post. Sharing is caring. One never knows, you may very well be helping someone out. I take joy in reading our article about Installing A Bathtub.
Get Started
Report this page